Modern alloying additions and binder phases for enhancing the performance of WC-based cemented carbides. A review

Classical alloying systems were developed in Germany in the 1920s–1930s: WC–Co (Osram), WC–TiC–Co, and WC–TiC–TaC–Co (Krupp AG). In the USSR, analogous materials were developed and standardized as the VK, TK, and TTK grade groups and found widespread application in cutting, drilling, stamping, and wear-resistant tooling. Since then, approximately 36,000 scientific papers aimed at improving the properties of cemented carbides have been published worldwide. Numerous alloying systems have been developed to enhance service performance while simultaneously reducing material consumption and production costs. There is a clear trend toward the design and application of multicomponent cemented carbides. This review is motivated by the need to develop new binder phases and alloying additions that increase strength, corrosion resistance, and microstructural uniformity under severe operating conditions. Given the projected growth in cemented carbide production and increasingly stringent service requirements, approaches aimed at reducing the content of costly cobalt while maintaining the current level of performance are of practical interest. To decrease the cobalt content without compromising the overall property set, Ni- and Fe-based binders are employed together with alloying additions of Cr, Mo, Mn, Al, and B. In addition, carbide grain-growth inhibitors, nanoscale oxide and rare-earth additives, and multicomponent binder solid solutions are used. The mechanisms by which various alloying components affect WC grain morphology and binder properties are discussed. In nearly all cases, the additions increase hardness, inhibit WC grain growth during sintering, and improve certain other properties. The review highlights the importance of consolidating and comparing data on the effects of alloying elements and binder-strengthening routes in the design of next-generation cemented carbides.

1. International tungsten industry association (ITIA). URL: https://www.itia.info/applications-markets/ (accessed: 14.06.2025).

2. Ruys A.J. Metal-reinforced ceramics. Amsterdam: Elsevier, 2020. 426 p. https://doi.org/10.1016/C2018-0-02083-6

3. Tungsten – global strategic business report. Research and markets. URL: https://www.researchandmarkets.com/reports/4721456/tungsten-global-strategic-business-report#src-pos-1 (accessed: 14.06.2025).

4. Farag S., Konyashin I., Ries B. The influence of grain growth inhibitors on the microstructure and properties of submicron, ultrafine and nano‑structured hardmetals – A review. International Journal of Refractory Metals and Hard Materials. 2018;77:12–30. https://doi.org/10.1016/j.ijrmhm.2018.07.003

5. García J., Collado Ciprés V., Blomqvist A., Kaplan B. Cemented carbide microstructures: A review. International Journal of Refractory Metals and Hard Materials. 2019;80:40–68. https://doi.org/10.1016/j.ijrmhm.2018.12.004

6. Marshall J.M., Giraudel M. The role of tungsten in the Co binder: Effects on WC grain size and hcp–fcc Co in the binder phase. International Journal of Refractory Metals and Hard Materials. 2015;49:57–66. https://doi.org/10.1016/j.ijrmhm.2014.09.028

7. Guo S., Bao R., Li S., Ye Y., Zhu E., Wang W., Zhang Y., Chen H., Ye Y. The role of Y2O3 , Cu, Mo and Mo2C additives on optimizing the corrosion resistance of WC–6Co cemented carbide in HCl and NaOH solutions. Journal of Alloys and Compounds. 2020;827:154269. https://doi.org/10.1016/j.jallcom.2020.154269

8. Yu B., Li Y., Lei Q., Nie Y. Microstructures and mechanical properties of WC–Co–xCr–Mo cement carbides. Journal of Alloys and Compounds. 2019;771:636–642. https://doi.org/10.1016/j.jallcom.2018.08.255

9. Mingard K.P., Roebuck B., Marshall J., Sweetman G. Some aspects of the structure of cobalt and nickel binder phases in hardmetals. Acta Materialia. 2011;59(6):2277–2290. https://doi.org/10.1016/j.actamat.2010.12.004

10. Cooper R., Manktelow S.A., Wong F., Collins L.E. The sintering characteristics and properties of hard metal with Ni–Cr binders. Materials Science and Engineering: A. 1988;105–106:269–273. https://doi.org/10.1016/0025-5416(88)90506-X

11. Ojo-Kupoluyi O.J., Tahir S.M., Baharudin B.T.H.T., Azmah Hanim M.A., Anuar M.S. Mechanical properties of WC-based hardmetals bonded with iron alloys – A review. Materials Science and Technology. 2017;33(5):507–517. https://doi.org/10.1080/02670836.2016.1186929

12. Wittmann B., Schubert W.-D., Lux B. WC grain growth and grain growth inhibition in nickel and iron binder hardmetals. International Journal of Refractory Metals and Hard Materials. 2002;20(1):51–60. https://doi.org/10.1016/S0263-4368(01)00070-1

13. Tarraste M., Antonov M., Kolnes M., Viljus M., Ormus A.-H. Erosive and impact‑abrasive wear of hardmetals with Fe‑based binders. Journal of the Japan Society of Powder and Powder Metallurgy. 2025;72:S1437–S1444. https://doi.org/10.2497/jjspm.16F-T15-05

14. Wu J., Ren D., Xie B., He R., Geng Z., Zhang Z., Liu Y., Wang D., Zhu Y., Zhang W. Effect of Cr3C2 addition on microstructure and mechanical properties of WC–CoNiFe cemented carbides. Metals. 2024;14(8):895. https://doi.org/10.3390/met14080895

15. Straumal B., Konyashin I. WC-based cemented carbides with high entropy alloyed binders: A review. Metals. 2023;13(1):171–186. https://doi.org/10.3390/met13010171

16. Weidow J., Norgren S., Andrén H.-O. Effect of V, Cr and Mn additions on the microstructure of WC–Co. International Journal of Refractory Metals and Hard Materials. 2009: 27(5):817–822. https://doi.org/10.1016/j.ijrmhm.2009.02.002

17. Long J., Zhang W., Wang Y., Du Y., Zhang Z., Lu B., Cheng K., Peng Y. A new type of WC–Co–Ni–Al cemented carbide: Grain size and morphology of γ′‑strengthened composite binder phase. Scripta Materialia. 2017;126:33–36. https://doi.org/10.1016/j.scriptamat.2016.08.007

18. Liu Y., Cheng J., Yin B., Zhu S., Qiao Z., Yang J. Study of the tribological behaviors and wear mechanisms of WC–Co and WC–Fe3Al hard materials under dry sliding condition. Tribology International. 2017;109:19–25. https://doi.org/10.1016/j.triboint.2016.12.023

19. Mosbah A.Y., Wexler D., Calka A. Abrasive wear of WC–FeAl composites. Wear. 2005;258(9):1337–1341. https://doi.org/10.1016/j.wear.2004.09.061

20. Johnson M., Mikkola D.E., March P.A., Wright R.N. The resistance of nickel and iron aluminides to cavitation erosion and abrasive wear. Wear. 1990;140(2):279–289. https://doi.org/10.1016/0043-1648(90)90090-W

21. Schneibel J.H., Carmichael C.A., Specht E.D., Subramanian R. Liquid-phase sintered iron aluminide‑ceramic composites. Intermetallics. 1997;5(1):61–67. https://doi.org/10.1016/s0966-9795(96)00066-0

22. Ahmadian M., Wexler D., Chandra T., Calka A. Abrasive wear of WC–FeAl–B and WC–Ni3Al–B composites. International Journal of Refractory Metals and Hard Materials. 2005;23(3):155–159. https://doi.org/10.1016/j.ijrmhm.2004.12.002

23. Habibi Rad M., Ahmadian M., Golozar M.A. Investigation of the corrosion behavior of WC–FeAl–B composites in aqueous media. International Journal of Refractory Metals and Hard Materials. 2012;35:62–69. https://doi.org/10.1016/j.ijrmhm.2012.04.005

24. Ahmadian M., Wexler D., Calka A., Chandra T. Liquid phase sintering of WC–FeAl and WC–Ni3Al compo­sites with and without boron. Materials Science Forum. 2003;426–432:1951–1956. https://doi.org/10.4028/www.scientific.net/MSF.426-432.1951

25. Lisovskii A.F. Cemented carbides alloyed with ruthenium, osmium, and rhenium. Powder Metallurgy and Metal Ceramics. 2000;39(9):428–433. https://doi.org/10.1023/A:1011306204246

26. U.S. Geological Survey, 2025, Mineral commodity summaries 2025 (ver. 1.2, March 2025): U.S. Geological Survey, 212 p. URL: https://pubs.usgs.gov/periodicals/mcs2025/mcs2025.pdf (accessed: 18.01.2025). https://doi.org/10.3133/mcs2025

27. Konyashin I., Farag S., Ries B., Roebuck B. WC–Co–Re cemented carbides: Structure, properties and potential app­lications. International Journal of Refractory Metals and Hard Materials. 2019;78:247–253. https://doi.org/10.1016/j.ijrmhm.2018.10.001

28. Adaskin A.M. Development of hard alloys based on tungsten carbide with cobalt-rhenium binder. Vestnik Mashinostroeniya. 2022;(11):72–76. (In Russ.). https://doi.org/10.36652/0042-4633-2022-11-72-76

29. Potgieter J.H., Thanjekwayo N., Olubambi P., Maledi N., Potgieter-Vermaak S.S. Influence of Ru additions on the corrosion behaviour of WC–Co cemented carbide alloys in sulphuric acid. International Journal of Refractory Me­tals and Hard Materials. 2011;29(4):478–487. https://doi.org/10.1016/j.ijrmhm.2011.02.007

30. Shing T.L., Luyckx S., Northrop I.T., Wolff I. The effect of ruthenium additions on the hardness, toughness and grain size of WC–Co. International Journal of Refractory Metals and Hard Materials. 2001;19(1):41–44. https://doi.org/10.1016/S0263-4368(00)00048-2

31. Kishino J., Nomura H., Shin S.-G., Matsubara H., Tana­se T. Computational study on grain growth in cemented carbides. International Journal of Refractory Metals and Hard Materials. 2002;20(1):31–40. https://doi.org/10.1016/S0263-4368(01)00068-3

32. ISO 4499-2. Hardmetals – Metallographic determination of microstructure – Part 2: Measurement of WC grain size: Geneva: ISO, 2020. 17 p.

33. Hayashi K., Fuke Y., Suzuki H. Effects of addition carbides on the grain size of WC–Co alloy. Journal of the Japan Society of Powder and Powder Metallurgy. 1972;19(2):67–71. https://doi.org/10.2497/jjspm.19.67

34. García J., Strelsky W. Process development and scale up of cemented carbide production. In: Scale‑up in metallurgy. Ed. M. Lackner. Vienna: Verlag ProcessEng Engineering GmbH, 2010. P. 235–266.

35. Schatt W., Wieters K.-P., Kieback B. Pulvermetallurgie: Technologien und Werkstoffe. 2nd ed. Berlin: Springer, 2007. 552 p.

36. Biurrun T.S. Sintering and mechanical properties of cemented carbides based on tungsten carbide and multicomponent metallic alloys. Donostia‑San Sebastián: University of Navarra School of Engineering, 2022. 175 p. https://doi.org/10.15581/10171/63228

37. Stoll W.M. Carbides, industrial hard. In: Kirk‑Othmer: Encyclopedia of chemical technology, 2003. P. 674–695. https://doi.org/10.1002/0471238961.0914042119201512.a01.pub2

38. Panov V.S., Zaitsev A.A. WC–Co hard alloys alloyed with tantalum carbide. Review. Powder Metallurgy аnd Functional Coating. 2015;(2):44–48. (In Russ.). https://doi.org/10.17073/1997-308X-2015-2-44-48

39. Kieffer R., Ettmayer P. Principles and latest developments in the field of metallic and nonmetallic hard materials. Angewandte Chemie International Edition in English. 1970;9(12):926–936. https://doi.org/10.1002/anie.197009261

40. Yin C., Ruan J., Du Y., Long J., Peng Y., Li K. Effects of Cr3C2 , VC, and TaC on microstructure, WC morphology and mechanical properties of ultrafine WC–10 wt. % Co cemented carbides. Metals. 2020;10(9):1211. https://doi.org/10.3390/met10091211

41. Fukatsu T., Kobori K., Ueki M. Micro-grained cemented carbide with high strength. International Journal of Refractory Metals and Hard Materials. 1991;10(2):57–60. https://doi.org/10.1016/0263-4368(91)90024-i

42. Guo S., Yan W., Yi J., Wang S., Huang X., Yang S., Zhang M., Ye Y. The optimization of mechanical pro­perty and corrosion resistance of WC–6Co cemented carbide by Mo2C content. Ceramics International. 2020;46(11):17243–17251. https://doi.org/10.1016/j.ceramint.2020.04.011

43. Soria T., Lopez B., Lozada L., Moseley S., Alveen P., Elsen M., Müller-Grunz A., Magin M., Useldinger R., Sánchez J.M. An investigation into the effects of HIP after sintering of WC–ZrC–Co–Cr3C2 cemented carbides. International Journal of Refractory Metals and Hard Materials. 2020;87:105164. https://doi.org/10.1016/j.ijrmhm.2019.105164

44. Nikolenko S.V., Verhoturov A.D., Dvornik M.I., Vlasova N.M., Pugachevsky M.A., Mihailov M.M., Krestjanikova N.S. Application of Al₂O₃ nanopowder as grain growth inhibitor in WC–8 %Co alloy. Voprosy Materialovedeniya. 2008;2(54):100–105. (In Russ.).

45. Min F., Wang S., Yu S., Yang H., Yao Z., Ni J., Zhang J. Enhanced coarse-grained WC–Co(Ce) cemented carbide prepared through co-precipitation. Materials. 2023;16(16):5506. https://doi.org/10.3390/ma16165506